Homelink Button Worked Once but Not Again

Programming Homelink® to Genie® Garage Door Openers

Helpful Tips

When programming, it helps to clear out your HomeLink by pressing and holding the outset and tertiary buttons down until
the indicator on the HomeLink blinks slow then fast (almost 20 seconds), and so release both buttons. If there is
something already programmed to your HomeLink do not articulate information technology unless y'all are able to reprogram what is already
on there.

First, Train HomeLink to any Genie Intellicode® Remote

You will demand to start with this step for each new opener head/HomeLink button combination. It is also recommended to consult the car's owner'south manual as individual auto manufacturers and models may have specific requirements related to that vehicle.

1. Choose a button on a Genie Intellicode remote* non yet programmed to your operator. The just reason to utilize a push button not even so programmed to your operator is to proceed the door from moving up and downward during programming. There is no event if you have the push button already programmed to the operator.

​

*If you lot accept chosen the G3T remote shown here, click the remote to view more than details

before standing to Stride 2. If this is non your remote, keep direct to Step 2 below.

2. Choose the button on your HomeLink that you want to use to open your door.

• If you lot are using one of the G3T remotes shown in the in a higher place pace or a G1T, continue with Step a).

• If you are not using ane of these remotes below, continue to Footstep b).
  

a) If y'all are using the three-button remote shown correct: From the previous Pace one c), please hold the same button you changed to the red LED for approximately ten seconds prior to pressing your HomeLink button (until both a ruby and green LED light prove again on this remote). Once both the cherry-red and dark-green LEDs light upwardly, then press your HomeLink button downward as well – holding both sets of buttons down until the indicator on the HomeLink blinks slowly and so fast. One time it goes fast, release both buttons.

If you are using the one-push remote G1T shown here: Please hold the push for
approximately 10 seconds prior to pressing your HomeLink push button, and so press your
HomeLink button downwards also – holding both sets of buttons down until the indicator
on the HomeLink blinks slowly and and so fast. Once it goes fast, release both buttons.

You are now gear up to programme your HomeLink to an opener. In the following

pages, please observe the document that suits your state of affairs and continue programming.

b) Hold down both the remote push button and your HomeLink button at the same fourth dimension. As you hold both buttons down, the indicator on your HomeLink should blink slowly then fast. Once information technology goes fast, release both buttons.

**Before moving on, if you have a Genie Model IntelliG® g, IntelliG® 1200, TriloG™ 1200, TriloG™ 1500, GPower™ 900, ReliaG® 650, or ReliaG® 850 and you lot are using an Intelligent Wall Console OR yous have this model and it was manufactured earlier July 2011, please run across the PDF version of instructions. If neither of these applies, delight continue below.

1. Press and release the learn code button - the red LED will begin to blink.

2. Press the desired HomeLink push one time. The ruby-red LED volition stop blinking and stay on.

3. Press the desired HomeLink button i more time. The red LED will become out.

4. Pressing the HomeLink button again will cause the garage door to move.

   NOTE: If you cannot notice your plan button on the powerhead, see the user transmission

Homelink® System Programming for newer Genie Models:

​

​

The steps below have a slight departure based on the date your garage door opener was manufactured.

In that location are steps for programming Homelink based on when your garage door opener was manufactured. If your series number has the first 5 digits of 11290 or smaller so your model was fabricated prior to November 2011. If your series number has the beginning 5 digits of 11291 or higher and then your model was fabricated after November 2011. Follow the appropriate instructions below.

Homelink® Arrangement Programming for newer Genie Models manufactured later on November 2011:

​

1. Press and concur the program button until the round blue LED is on – release the button. The long LED will flash purple.

2. Printing the desired HomeLink button for one second and release information technology. Press that same button over again for one 2nd and release. The round LED and long LED will both turn blueish and then plow off.

3. Pressing the HomeLink push button again will cause the garage door to movement.
   

Notation: If yous cannot discover your program push on the powerhead, see the user manual

Homelink® System Programming for newer Genie Models manufactured earlier November 2011:

​

1. Printing and concur the program button until the round blue LED and the long blue LED are on – release the button. The circular blue LED volition be on.

2. Press the program button once - the long purple LED will begin flashing.

3. Press the desired HomeLink push button for one 2nd and release it. Printing that aforementioned button once more for one 2nd and release. The long LED volition wink blue and and so turn off.

4. Pressing the HomeLink push over again will crusade the garage door to motility.
   

Note: If you lot cannot detect your plan push button on the powerhead, see the user manual

poolemothe1945.blogspot.com

Source: https://www.geniecompany.com/homelink-programming

Share this post